Common Defeats In Denim Jeans Sewing:

American and Efird – has listed out some of the most common seam inequalities in the manufacturing of denim jeans . The company lists out the defects and suggests solutions for removing these defects. We are summarizing the results from A & E  below :

 1.BROKEN STITCHES – NEEDLE CUTTING

Description : Where the thread is being broken where one seam crosses another seam (ex: bar-tacks on top of waistband stitching, seat seam on top of riser seam ) resulting in stitch failure.

Recommended solution by A & E :

• Use a larger diameter thread on operations where the thread is being cut.
• Make sure the proper stitch balance is being used. On a chain stitch seam on denim, you normally would like to maintain a 60%/40% relationship of Needle thread to Looper thread in the Seam.
• Use needles with the correct needle point.
• Change the needles at regular intervals on operations where the Needle Cuts are occurring frequently.
• Use a higher performance  Perma Core or D-Core thread.

2.Broken Stitch – Abrasion :

Description: where the thread is broken during stone-washing, sand blasting, hand sanding, etc.  Broken stitches must be repaired by restitching over the top of the stitch-line.

Recommended Solution :

• Use a larger diameter thread on operations where
  excessive abrasion is occuring  (ex: use T-120 on
  Waistband);
• Make sure stitches are balanced properly.
• Use a Magic air entangled thread in the looper due to its lower
  seam profile making it susceptible to abrasion
  (ex: use T-90 or T-135 Magic in loopers of the Yoke, Seat
  and Waistband seam);
• Monitor the Finishing Cycle for compliance to specs.

3. Broken Stitches : Chemical Degradation :

Description : where thread is  being compromised by the chemicals used during laundering resulting in loss or change of color and seam failure.

• It is recommended to go to larger thread sizes when the
  Denim Garments will be subject to Harsh Chemical
  washes.
• To achieve the best laundering results make
  sure that the water temperatures and PH Levels are
  correct and that the proper amounts and sequence of
  chemical dispersion are within guidelines.
• Make sure the garments are being rinsed properly to neutralize the
  chemicals in the fabric.
• Monitor the drying process, cycle times, and temperatures to make sure they are correct so that the best possible garment quality can be
  achieved.

4. Unravelling Seams :

Description : where either the stitch has been broken or a skipped stitch has
occurred. This will cause seam failure unless the seam is Restitched.

Recommended Solution :

• This may include going to a higher performance thread designed to minimize sewing
  interruptions.
• Observe sewing operators for correct material handling techniques.

6. Sagging or Rolling Pockets :

Description :  where the pocket does not lay  SAGGING OR ROLLING POCKETS  flat and rolls over after laundering.

Recommended Solution :

• Make sure the sewing operators are not holding POCKETS
  back excessively when setting the front pocket.
• Make sure the hem is formed properly and that excessive
  fabric is not being being put into the folder that will cause
  the hem to roll over.
• Check to make sure pocket is cut properly and that pocket curve is not too deep.
• Use a reinforcement tape on the inside of the pocket that may
  help prevent the front panel from stretching along the bias
  where the front pocket is set.
• The type and weight of denim, along with the fabric construction, may contribute to this problem. Contact your fabric supplier for assistance.

5.Skipped Stitches

Description: where the stitch forming device misses the
needle loop or the needle misses the looper loop. Skips are usually
found where one seam crosses another seam and most of the time
occurs right before or right after the heavy thickness.

Recommended Solution :-

• Use core spun thread.
• Use minimum thread tension to get a balanced stitch.
• Use the ideal foot, feed and plate that helps to minimize
  flagging.
• Training sewing operators NOT to stop on the
  thickness.
• Make sure the machine is feeding properly
  without stalling.
• Make sure the machine is not back-feeding.

6. Ragged – Inconsistent Edge

Description : where the edge of the seam is
either extremely “ragged” or “rolls” inside the stitch.

Recommended Solution :

• Make  sure the sewing machine knives are sharpened and
  changed often.
• The knives should be adjusted properly in relationship to the “stitch tongue” on the needle plate to obtain the proper seam width or width bite.

7. Wavy Seams On Stretch Denim

Description : where the seam does not lay  flat and is wavy due to the fabric stretching as it was sewn or during subsequent laundering and handling operation.

Recommended Solution : 

• Use minimum presser foot pressure.
• Instruct sewing operators to use proper handling techniques and not
  stretch the fabric as they are making the seam.
• Where available, use differential feed to compensate for the
  stretch of the fabric.

8. Ropy Hem

Description: is where hem is not laying flat and is skewed in  ROPY HEM
appearance .

Recommended Solutions :

• Instruct the sewing operator to make sure they get the hem started correctly in the folder before they start sewing.
• Also, make sure the don’t hold back
  excessively as the seam is being sewn.
• Use minimum roller or presser foot pressure.

9. Twisted Legs :

Description : is where the side seam twists around to the front   of the pant and distorts the appearance of the jeans .

Recommended Solution :

• Instruct the sewing operator to
  match the front and back properly so they come out the
  same length. Sometimes notches are used to insure proper
  alignment. They should NOT trim off the front or back with
  scissors to make them come out the same length.
• Make sure the cut parts are of equal length coming to the
  assembly operation.
• Check fabric quality and cutting for proper skew.
• Make sure the sewing machine is adjusted
  properly for uniform feeding of the top and bottom plies

8. Disappearing Stitches in Stretch Denim

Description :  is where the  thread looks much smaller on seams sewn in the warp direction than in the weft direction of the fabric

Recommended Solution :

• Use a heavier thread size (T-120,  ON STRETCH DENIM
  T-135, T-150) on top stitching.
• Go to a longer stitch length  (from 8 to 6 spi). 3) Make sure the thread tensions are as loose as possible so the thread sits on top of the
  fabric rather than burying in the fabric on seams sewn in
  the warp.

10. Thread Discoloration after Laundry

Description: is where the thread pics up the indigo dyes from the fabric giving the thread a ‘dirty’ appearance. A common discoloration would be the pick-up of a greenish or turquoise tint.

Recommended Solution :

• Use thread with proper color fastness characteristics.
• Correct PH level (too low) and Water Temperature (too low) during laundry.
• Use the proper chemicals & laundry cycles.
• Use Denimcol PCC in wash or similar additive.
• Do Not overload washers with too many garments at one time